Carbon Monoxide – What You Need To Know

What is Carbon Monoxide (CO)?

CO is a colorless, odorless, tasteless gas
It is a by-product of incomplete combustion (unburned fuel such as gas, oil, wood, etc.)
Low concentrations of CO can go undetected and can contribute to ongoing, unidentified illnesses. At high concentrations, it can be deadly.

Why is it Dangerous?

If there is CO in the air you breath, it will enter your blood system the same way oxygen does through your lungs. The CO displaces the oxygen in your blood, depriving your body of oxygen. When the CO displaces enough oxygen, you suffocate.

What are the Symptoms?

Continued exposure or high concentrations can result in –

Confusion
Severe headaches
Cardiac problems
Breathing difficulties
Brain damage
Dizziness
Death

Long term exposure to low concentrations –

Slight headaches
Fatigue
Shortness of breath with only moderate exertion
Nausea
Dizziness and confusion

Why is it called "The Great Imitator"?

Symptoms of CO poisoning are very similar to the flu
Illness in pets preceding illness in a family member may suggest CO poisoning

Who is at Greater Risk?

Senior citizens
Unborn babies
People with respiratory or coronary problems
Infants
Pregnant women
Young children

Note: Vulnerable people who are exposed even to low levels of CO for long time periods may have similar health affects as those exposed to high concentrations of CO.

What can Produce CO in our Homes

Anything that burns fuel or generates combustion gases including -

Gas Stoves
Fireplaces
Automobiles
Barbecues
Furnaces
Ranges
Boilers
Space heaters
Water heaters
Portable generators

Solid fuels, such as wood, always produce carbon monoxide when they are burned. Gas and liquid fuels may produce no CO or very little.

What are the most common sources of Carbon Monoxide?

1. Automobile exhaust in attached garages.
This is responsible for 60% of all CO alarms. People who warm their cars up in the garage are trapping CO inside the garage. The CO can find its way into the home.

2. Gas cooking appliances.
This is reported to account for 20% of CO alarms. It may be a result of a misused, poorly maintained, poorly installed, or unvented cooking appliance.

3. Poor draft/venting for fuel burning appliances.
This is one of the most common and serious causes for CO build-up and has been reported to account for up to 19% of CO alarms. The products of combustion are not being safely expelled to the exterior. This could be due to venting problems, such as blocked chimney flues or inadequate venting for appliances or fireplaces. Other problems include poor installation and negative air pressure in the house, causing backdrafting, often due to exhaust fans.

Other problems include poor combustion at furnace. Inadequate combustion air to the furnace can result in incomplete combustion. If the furnace has a cracked heat exchanger, it is possible to get CO into the circulating air. It is also imperative that we do not deprive our heating equipment and fuel burning appliances of air; especially in air-tight homes where running exhaust fans can result in a shortage of combustion air. Combustion air is essential for safe operation of furnaces, water heaters, and other fuel burning equipment.

There can also be a leak in a chimney or flue pipe.

Ventilation issues are very common as a result of barbecues or gasoline powered equipment operating in an attached garage, basement, or enclosed area.

Are there more problems with carbon monoxide today than 30 years ago?
Yes, this is due to:

More energy-efficient, air-tight homes
Less natural ventilation

How can I guard against carbon monoxide poisoning?

The first line of defense is to have your home heating systems, fuel burning appliances, flues and chimneys checked and/or cleaned annually.

Here is the inspection checklist. Specialists should check for:

Blocked openings to flues and chimneys
Cracked, rusted, or disconnected flue pipes
Dirty filters
Rusted or cracked heat exchanger
Soot or creosote build-up inside fireplaces and chimney flues
Exhaust or gas odors
Attached garages require gas proofing and automatic closers for doors into the home
Adequate combustion air
Adequate venting on indoor combustion appliances (i.e-gas stoves)

The second line of defense is a CO detector.

Carbon Monoxide Detectors

Background

It’s a relatively new technology introduced in the early 1990s. It is designed to warn homeowners when CO reaches dangerous levels within the home.

How do they work?

CO detectors sample the air at specific time intervals. A microchip inside the detector stores the reading and keeps track of the level of CO that the detector is exposed to over time

Types of sensors:

Residential

Biometric (Oldest type of sensor)
Metal Oxide Semi-conductor
Electrochemical (The best of the three types for a residential sensor)

Industrial

Infrared – Highly advanced, very expensive. Not something you would find at a typical hardware store.

The detectors are supposed to sound an alarm when exposed to a set level of CO (measured in parts per million) over a specific time period. These levels or standards are set by UL (Underwriters Laboratories).

Old Standard (Units manufactured between October 1, 1995 and October 1, 1998) - First Generation CO detectors.

Exposure	CO (ppm)	Time
To a low level for a prolonged period of time	15	Alarm after 30 days
To a low level of CO for an extended period of time	100	Alarm within 90 minutes
To a moderate level of CO for a shorter period of time	200	Alarm within 35 minutes
To a high level of CO for a short period of time	400	Alarm within 15 minutes

The UL Standard was revised and any detector manufactured after October 1, 1998 must conform to the new Standard.

Exposure	CO (ppm)	Time
To a low level for a prolonged period of time	30	Alarm after 30 days
To a low level of CO for an extended period of time	70	Alarm within 189 minutes
To a moderate level of CO for a shorter period of time	150	Alarm within 50 minutes
To a high level of CO for a short period of time	400	Alarm within 15 minutes

Also included in the new Standard is:

CO detector should ignore a CO level reading of 70 for at least 1 hour without alarming
CO detector should ignore a CO level reading of 150 for at least 10 minutes without alarming
Must only signal under alarm or trouble. No low-level warning signal is allowed
Must have a SILENCE button to shut it off. Must re-alarm after 6 minutes if CO levels persist
Must meet the specificity test referencing non-alarm status at specific concentrations of certain gases and vapors

To put levels into perspective:

CO Level (ppm)	Health Effect
0	Desirable level
9	Maximum outdoor air quality level as per EPA
50	Maximum concentration for a continuous exposure in an 8-hour time period (OSHA standard)
400	Headaches in 1 to 2 hours, life threatening after 3 hours
800	Nausea and convulsions, death within 2 hours
1600	Nausea within 20 minutes, death within 1 hour
12,800	Death within 1 to 3 minutes

Note: These studies are generally done on young, healthy people. These symptoms can change drastically depending on age, sex, weight, habits (e.g. smoking), and most importantly, your health.

The Controversy

Reliability of the detectors

The Issue

CO detectors are supposed to alarm at certain levels as indicated in the tables above
Recent testing suggests that many of these devices are not nearly as reliable as they should be
There has been regular television coverage that focused on false alarms and the reliability of CO detectors

Example

In 1994, Chicago was the first major city to make these detectors mandatory in the living space
In the last three months of 1994, the Chicago Fire Department responded to 8,600 CO alarms
In almost every case there was no dangerous level of CO found during follow-up investigations

Result

Laboratory testing was done
Up to 1/3 of the alarms tested, failed to alarm

Reasons

1. Technology

Technology for residential CO detectors is very primitive.
Industrial detectors have a different set of standards and more sophisticated technology. As a result, they are very expensive.
Different detectors have large variances on the levels at which they are supposed to alarm. The sensor technology used in home alarms is not designed to measure and display low level, short term concentrations of CO. Substantial differences exist in the sensitivity of different sensors at low levels. As a result, they may go off too soon or not soon enough.

2. Humidity

Standards require these devices to be tested at a humidity of 50%.
Testing revealed that many devices failed to respond when humidity levels were low even though they are supposed to work within a large humidity range. See your CO detectors manual.
In colder climates, humidity levels can fall well below 50% (in fact the humidity should not be higher than 40%) during the cold season when furnaces and other fuel burning appliances are in full operation.

3. Effect of Other Gases and Vapors

Other gases such as Carbon Dioxide can also trigger a CO alarm. The UL 2034 Standard requires that CO alarms do not alarm when certain concentrations of other gases and vapors exist in the vicinity of a CO detector. The level for Carbon Dioxide in the old standard was low, which may have contributed to many false alarms with first generation CO detectors.

Conclusions

CO detectors are designed to protect the average healthy human from death or serious injury under the current standards; however –
People who are more susceptible cannot depend on these devices for total protection. In this case, more sensitive CO detecting equipment should be used.
Several groups are working with UL to improve the standards. October 1999 revisions have already been drafted.
There is room for improvement by imposing stricter standards as well as technological development.
It is critical that people understand the dangers of CO and that the people who investigate it are properly trained and are using CO testing equipment properly.

Where to install a CO detector?

One or more CO detectors in accordance with the manufacturer’s recommendations. Usually one per floor.
Maintain and test regularly as instructed by the manufacturer.

Things to look for when buying a CO detector?

Type of sensor (electrochemical)
Certification-UL 2034
Conforms to new standard
IAS 6-96 is a supplementary standard to the UL 2034 which includes reliability testing. This standard may not be visible on the box.
Other considerations include digital display, sensor life, power source, and warranty.

How does all of this relate to your home inspection?

A home inspection may reveal a potential Carbon Monoxide source.
Common deficiencies found during inspections include:

Venting deficiencies
Damaged or rusted flue pipes
Dirty or blocked chimney flues
Cracked heat exchangers
Gas proofing deficiencies
Inadequate combustion air
Poorly installed equipment

Limitations –

Visual Inspection
Equipment available

There are other ways to test CO levels in a home. These tests go beyond the scope of a standard home inspection.

Line drawings are from the Carson Dunlop Home Inspection Training Program and Home Inspection Software Tool – Horizon

Book your inspection

Structures 101 – What You Should Know About The “Bones”

"This house isn't going anywhere." Or is it!?

Uneven Floors

Leaning House

Horizontal Foundation Cracks are Bad

Harmless Cracks

Plaster Cracks: